| Code |
Description |
Trooble shooting |
| Location 1: WebC errors |
| 10 |
Communication errors |
|
| 10:01 |
No communication |
|
| 10:02 |
Checksum error |
|
| 10:03 |
Bad quality of the data stream |
|
| 10:04 |
bad quality of bytes |
|
| 11 |
Communication errors |
|
| 11:01 |
No communication |
|
| 11:02 |
Checksum error |
|
| 11:03 |
Bad quality of the data stream |
|
| 11:04 |
bad quality of bytes |
|
| Location 2: Fan Folder errors |
| 21 |
Error on stepper control boards |
|
| 21:01 |
Error on starting stepper control board |
|
| 21:02 |
Error on stopping stepper control board |
|
| 22 |
Sensor errors on start-up |
|
| 22:00 |
Sensor LB0 cut |
|
| 22:01 |
Sensor LB1 cut |
|
| 22:02 |
Sensor LB2 cut |
|
| 22:03 |
Sensor LB3 cut |
|
| 22:04 |
Sensor LB4 cut |
|
| 23 |
Sensor sends high level permanently |
|
| 23:00 |
Sensor LB0 |
|
| 23:01 |
Sensor LB1 |
|
| 23:02 |
Sensor LB2 |
|
| 23:03 |
Sensor LB3 |
|
| 23:04 |
Sensor LB4 |
|
| 24 |
Processing errors on stepper control boards |
|
| 24:01 |
Error while calculating the step |
|
| 24:02 |
Error while counting the steps |
|
| 25 |
hardware errors |
|
| 25:01 |
Lack of 5 Volts external |
|
| 25:02 |
Lack of 38 Volts in FF or CF door open |
|
| 25:03 |
Cover open |
|
| 26 |
Time out errors |
|
| 26:01 |
No ready signal after paper cut |
|
| 26:02 |
No paper at sensor LB1 after paper cut |
|
| 26:03 |
No paper at sensor LB1 without cut signal |
|
| 26:04 |
Jam between sensors LB0 and LB1 |
|
| 26:05 |
No trailing edge of the paper at sensor LB1 |
|
| 26:06 |
Too many folds, document is too long |
|
| 26:07 |
No trailing edge of the paper at sensor LB0 |
|
| 26:08 |
Unexpected paper at sensor LB4 in Online-Mode |
|
| 26:09 |
Unexpected paper at “no fold” switch LB5 in Online-Mode |
|
| Location 3: Cross Folder errors |
| 80 |
Hardware errors |
|
| 80:01 |
Lack of 5 Volts external |
|
| 80:02 |
Lack of 38 Volts in FF or CF door open |
|
| 80:03 |
Lack of 28 Volts |
|
| 81 |
Error on stepper control boards |
|
| 81:01 |
Error on starting stepper control board |
|
| 81:02 |
Error on stopping stepper control board |
|
| 82 |
Sensor errors on start-up |
|
| 82:01 |
Sensor LB12 cut |
|
| 82:03 |
Sensor LB10 cut |
|
| 82:04 |
Sensor LB13 cut |
|
| 83 |
Sensor sends high level permanently |
|
| 83:01 |
Sensor LB12 |
|
| 83:02 |
Sensor LB11 |
|
| 83:03 |
Sensor LB10 |
|
| 83:04 |
Sensor LB13 |
|
| 84 |
Time out errors |
|
| 84:01 |
Sensor LB11 |
|
| 84:02 |
Sensor LB12 |
|
| 84:03 |
Sensor LB13 |
|
| 84:04 |
Paper did not reach the CF exit switch |
|
| 84:05 |
Jam at CF exit switch |
|
| 84:06 |
Jam at sensor LB10 |
|
| 85 |
Paper jam |
|
| 85:01 |
Jam at sensor LB11 |
|
| 85:02 |
Jam at sensor LB12 |
|
| 86 |
Error at roll tray motor end stage |
|
| 86:01 |
Error while moving forward |
|
| 86:02 |
Error while moving backward |
|
| 86:03 |
Error while trying to stop |
|
| 86:04 |
Error during initialisation |
|
| Location 4: Tab Applicator |
| 41:01 |
Tab unit is not ready |
|
| 41:02 |
Error at motor end stage |
|
| 41:03 |
No tape inside the unit or sensor is damaged |
|
| 41:04 |
Jam close to the knife |
|
| Errors in modules |
| 01xx... |
In any case the code atarts with 01 check the sensors in diagnostics |
|
| 02 |
Initialisation error |
|
| 03 |
Error on linear activator |
|
|
Module 1: Stacking unit |
|
| 02 |
Initialisation error |
|
|
Module 2: Tab application unit |
|
| 01 0x01 |
Switch in position 198mm or 11 inches |
|
| 01 0x02 |
Switch in position 210mm or 12 inches |
|
| 02 |
Initialisation error |
|
| Communication error between WebC and modules |
| 20:xx |
WebC and Module 0 |
|
| 21:xx |
WebC and Module 1 |
|
| 22:xx |
WebC and Module 2 |
|
| 23:xx |
WebC and Module 3 |
|
| xx:01 |
No communication |
|
| xx:02 |
Checksum error |
|
| xx:03 |
Bad quality of the data stream |
|
| xx:04 |
bad quality of bytes |
|
| F1CA |
CAN-bus error |
|