Code |
Description |
Trooble shooting |
Location 1: WebC errors |
10 |
Communication errors |
|
10:01 |
No communication |
|
10:02 |
Checksum error |
|
10:03 |
Bad quality of the data stream |
|
10:04 |
bad quality of bytes |
|
11 |
Communication errors |
|
11:01 |
No communication |
|
11:02 |
Checksum error |
|
11:03 |
Bad quality of the data stream |
|
11:04 |
bad quality of bytes |
|
Location 2: Fan Folder errors |
21 |
Error on stepper control boards |
|
21:01 |
Error on starting stepper control board |
|
21:02 |
Error on stopping stepper control board |
|
22 |
Sensor errors on start-up |
|
22:00 |
Sensor LB0 cut |
|
22:01 |
Sensor LB1 cut |
|
22:02 |
Sensor LB2 cut |
|
22:03 |
Sensor LB3 cut |
|
22:04 |
Sensor LB4 cut |
|
23 |
Sensor sends high level permanently |
|
23:00 |
Sensor LB0 |
|
23:01 |
Sensor LB1 |
|
23:02 |
Sensor LB2 |
|
23:03 |
Sensor LB3 |
|
23:04 |
Sensor LB4 |
|
24 |
Processing errors on stepper control boards |
|
24:01 |
Error while calculating the step |
|
24:02 |
Error while counting the steps |
|
25 |
hardware errors |
|
25:01 |
Lack of 5 Volts external |
|
25:02 |
Lack of 38 Volts in FF or CF door open |
|
25:03 |
Cover open |
|
26 |
Time out errors |
|
26:01 |
No ready signal after paper cut |
|
26:02 |
No paper at sensor LB1 after paper cut |
|
26:03 |
No paper at sensor LB1 without cut signal |
|
26:04 |
Jam between sensors LB0 and LB1 |
|
26:05 |
No trailing edge of the paper at sensor LB1 |
|
26:06 |
Too many folds, document is too long |
|
26:07 |
No trailing edge of the paper at sensor LB0 |
|
26:08 |
Unexpected paper at sensor LB4 in Online-Mode |
|
26:09 |
Unexpected paper at “no fold” switch LB5 in Online-Mode |
|
Location 3: Cross Folder errors |
80 |
Hardware errors |
|
80:01 |
Lack of 5 Volts external |
|
80:02 |
Lack of 38 Volts in FF or CF door open |
|
80:03 |
Lack of 28 Volts |
|
81 |
Error on stepper control boards |
|
81:01 |
Error on starting stepper control board |
|
81:02 |
Error on stopping stepper control board |
|
82 |
Sensor errors on start-up |
|
82:01 |
Sensor LB12 cut |
|
82:03 |
Sensor LB10 cut |
|
82:04 |
Sensor LB13 cut |
|
83 |
Sensor sends high level permanently |
|
83:01 |
Sensor LB12 |
|
83:02 |
Sensor LB11 |
|
83:03 |
Sensor LB10 |
|
83:04 |
Sensor LB13 |
|
84 |
Time out errors |
|
84:01 |
Sensor LB11 |
|
84:02 |
Sensor LB12 |
|
84:03 |
Sensor LB13 |
|
84:04 |
Paper did not reach the CF exit switch |
|
84:05 |
Jam at CF exit switch |
|
84:06 |
Jam at sensor LB10 |
|
85 |
Paper jam |
|
85:01 |
Jam at sensor LB11 |
|
85:02 |
Jam at sensor LB12 |
|
86 |
Error at roll tray motor end stage |
|
86:01 |
Error while moving forward |
|
86:02 |
Error while moving backward |
|
86:03 |
Error while trying to stop |
|
86:04 |
Error during initialisation |
|
Location 4: Tab Applicator |
41:01 |
Tab unit is not ready |
|
41:02 |
Error at motor end stage |
|
41:03 |
No tape inside the unit or sensor is damaged |
|
41:04 |
Jam close to the knife |
|
Errors in modules |
01xx... |
In any case the code atarts with 01 check the sensors in diagnostics |
|
02 |
Initialisation error |
|
03 |
Error on linear activator |
|
|
Module 1: Stacking unit |
|
02 |
Initialisation error |
|
|
Module 2: Tab application unit |
|
01 0x01 |
Switch in position 198mm or 11 inches |
|
01 0x02 |
Switch in position 210mm or 12 inches |
|
02 |
Initialisation error |
|
Communication error between WebC and modules |
20:xx |
WebC and Module 0 |
|
21:xx |
WebC and Module 1 |
|
22:xx |
WebC and Module 2 |
|
23:xx |
WebC and Module 3 |
|
xx:01 |
No communication |
|
xx:02 |
Checksum error |
|
xx:03 |
Bad quality of the data stream |
|
xx:04 |
bad quality of bytes |
|
F1CA |
CAN-bus error |
|